Msd Pro Billet Distributor Wiring Diagram

Understanding the MSD Pro Billet Distributor

The MSD Pro Billet Distributor is a high-performance electronic ignition system designed to improve engine performance and fuel efficiency. This device is an upgrade to the traditional distributor, allowing for superior spark control and execution. Thanks to its cutting-edge technology, the MSD Pro Billet Distributor can provide up to 16 times more electricity than a standard distributor.

In order to take advantage of the MSD Pro Billet Distributor, you must first understand the basics of wiring it into your engine. Although the process is slightly more complicated than a traditional distributor installation, it is still quite straightforward and relatively easy to complete. To ensure a proper installation, it is important to understand both the firing order and the voltage requirement.

How to Wire an MSD Pro Billet Distributor

The MSD Pro Billet Distributor requires two wires to be connected to the coil in order to supply power. First, the red wire must be connected to the positive terminal of the coil, and the black wire must be connected to the negative terminal. Then, the orange wire should be connected to the ignition switch. Finally, the remaining wires should be connected to the appropriate terminals on the distributor cap.

It is important to note that the polarity of the wires must be strictly observed when wiring the MSD Pro Billet Distributor. Failing to adhere to the correct wiring instructions can lead to severe damage to the ignition system. Therefore, it is highly recommended that a professional mechanic be consulted if any questions arise during the installation process.

Firing Order for an MSD Pro Billet Distributor

For optimal performance of an MSD Pro Billet Distributor, it is essential to ensure that the correct firing order is applied. The firing order for an MSD Pro Billet Distributor is 1-8-4-3-6-5-7-2. This order must be followed precisely, as incorrect wiring can cause misfires and other issues.

It is also important to note that the MSD Pro Billet Distributor is designed for use with a standard four-cylinder engine. It is not suitable for use with engines with more than four cylinders, as the firing order differs significantly from the one stated above.

Benefits of Using an MSD Pro Billet Distributor

The MSD Pro Billet Distributor offers a number of benefits to any engine. These include increased power and torque, improved fuel efficiency, smoother idle, and improved engine response. In addition, the MSD Pro Billet Distributor offers enhanced spark control, allowing for precise timing of the spark plugs.

The MSD Pro Billet Distributor also offers a wide range of customization options. With its adjustable mechanical advance and vacuum advance, you can tailor the distributor to suit the specific needs of your engine. Furthermore, the MSD Pro Billet Distributor is compatible with a wide range of ignition systems, allowing for greater flexibility for those who want to experiment with different brands of electronic controllers.

Using an MSD Pro Billet Distributor with a Stock Ignition System

The MSD Pro Billet Distributor is perfectly capable of being used with a stock ignition system. However, there are some important considerations to make before installing the distributor. Firstly, the MSD Pro Billet Distributor requires a 12 volt DC power source, so it is necessary to connect it directly to the battery or to a dedicated power source. Secondly, the MSD Pro Billet Distributor must be wired correctly to ensure that the firing order is correct. Finally, the timing must be set to ensure that the spark plugs fire at the correct interval.

Once these steps have been taken, the MSD Pro Billet Distributor can be used with a stock ignition system without any additional modifications. Doing so will result in improved performance, better fuel economy, and more precise spark control.

Adjusting the Timing on an MSD Pro Billet Distributor

Adjusting the ignition timing on an MSD Pro Billet Distributor is a simple but important task. In order to adjust the timing, it is necessary to make use of the adjustable mechanical advance and vacuum advance. By adjusting the advance, you can fine-tune the distributor to suit the specific needs of your engine.

To adjust the timing, start by setting the initial timing to 10° BTDC (Before Top Dead Center). Then, you can begin to adjust the mechanical advance by turning the screws clockwise. Once the desired advance has been obtained, you can then adjust the vacuum advance by either increasing or decreasing the amount of vacuum to the advance mechanism. Once all adjustments have been completed, you can then test the timing to ensure that the engine is running optimally.

Warranty on an MSD Pro Billet Distributor

The MSD Pro Billet Distributor comes with a limited lifetime warranty. This warranty covers the distributor against any defects in material and workmanship, as well as any electrical or mechanical malfunctions. Furthermore, the warranty also covers any damage caused by normal wear and tear.

In order to obtain warranty coverage, the distributor must be registered within 30 days of the date of purchase. If the distributor fails to perform as promised, the customer can contact MSD for assistance. MSD will then inspect the distributor and if any issues are found, they will repair or replace the defective part free of charge.

Using Other Brands of Ignition Control with an MSD Pro Billet Distributor

The MSD Pro Billet Distributor is designed to be compatible with a wide range of ignition control systems, including other brands such as Accel and Mallory. However, it is important to note that some components may need to be adjusted or replaced in order for the distributor to function properly.

For example, if you are using an Accel ignition control, you may need to replace the trigger plate on the distributor with an Accel-specific version. Similarly, if you are using a Mallory ignition control, you may need to replace the mechanical advance springs with Mallory-specific versions. As such, it is advisable to consult with a professional before attempting to use the MSD Pro Billet Distributor with another brand of ignition control.

Difference Between Mechanical and Vacuum Advances in an MSD Pro Billet Distributor

The MSD Pro Billet Distributor features both a mechanical advance and a vacuum advance. The mechanical advance is controlled by the distributor itself, while the vacuum advance is controlled by the pressure of the intake manifold.

The main difference between the two advances is that the mechanical advance is designed to increase the spark timing as the engine RPMs increase, while the vacuum advance is designed to decrease the spark timing as the engine RPMs increase. This helps to ensure that the spark is delivered at the optimal point in the combustion cycle, resulting in improved performance and fuel efficiency.